Then we turn the work over to the wrong side and again "turn the page". Without changing the position of the figure, we take the right corner of the diamond and "turn the page". Turn the work, turn the lower corner upwards, so that the rhombus turns out on this side too. Raise the bottom corner of the face layer upwards. Its only acute angle is directed towards you. The "table-top" (the smaller of the visible squares) is pressed inward. After this, add the "table" in the manner shown in the photo. We have a three-dimensional small table on massive legs. We unfold the whole structure as shown in the photo. Turn the work to the other side, again bend the corner to the point of intersection and return to its original position. We return the corner to its former position. Bend the upper corner to the point of intersection of the twofold lines. It was a quadrilateral with two short and two long sides. We turn the work and perform the operation again. The upper corner of the diamond is lowered to the bottom. Similarly, raise the bottom corner to make a rhombus. On the obverse side, a rhombus turned out, although on the right side - while the square is preserved. The right and left corners will turn around and lie down to the center line. The fold line coincides with the base line of the inscribed isosceles triangle, which we discussed in the previous steps. The bottom corner of the square is lifted up. The square lies so that the vertex of the inscribed isosceles triangle is directed towards you, and the bottom is on top. We see that on the square there are three fold lines that form an inscribed isosceles triangle. Then turn the work to a small square from the third step. Bend the top corner so that it turned outisosceles triangle. Without changing the position of the part, bend the right and left corners to the center line. Close the folds of the upper half of the diagonal. To the lower half of this diagonal, we fold the right and left parts of the second diagonal. Put the square in front of you in such a way that one of the diagonals was directed towards you. Fold the square in half, rotate the part 90 degrees and again fold it in half. Fold the square in two diagonals, then unfold. If not, then it's okay - our origami from paper dragon is simple and affordable. If you had previously encountered the world of origami, then probably you did a classic crane. There are huge modular figures and solid, composite of several sheets simple and light dragons for beginners, as well as complex and moving for more skillful masters. There are various origami schemes, how to make a dragon. In many cultures, the dragon is a symbol of wisdom. Our origami dragon is the same as in the ancient paintings: proud and unapproachable and at the same time very elegant. This is one well-loved origami and we've received many photos from readers who've folded it.Many people want to find a scheme of origami dragon, because inall fairy tales and legends they act as both good and evil characters. Origami Dinosaur Step 8: Now fold the lower part of the body inside, to slim the creature down a bit:Īnd there you have it, a fearsome origami dinosaur! Then crease each of the rear legs as shown, and do a crimp fold to form the feet: then repeat on the backside to form the other leg. Fold corner C downwards to form one of the rear legs. Origami Dinosaur Step 6: An inside front fold forms the animal's front legs. Origami Dinosaur Step 5: And do a reverse outside fold to start forming the head of the dinosaur, and an inside reverse fold to complete it. Origami Dinosaur Step 4: Next is a reverse outside fold to move corner B to a vertical position: Then rotate it 180 degrees counter-clockwise: Origami Dinosaur Step 3: Now fold the model in half along the long axis. Origami Dinosaur Step 2: Fold corner A of the bird base downwards as shown below. Origami Dinosaur Step 1: Fold an origami bird base using a square 6" x 6" (15cm x 15cm) origami paper. Made this origami? Comment and Submit your photo using the comment box at the end of this page!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |